Product thermal capacity : 1-20 t/h Working pressure : 0.7-2 Mpa Available fuel : Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc. Available industries : Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc. Introduction:
flue gas boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
Technical advantages Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
|2019-5-19 · Flue gas is the gas exiting to the atmosphere via a flue, which is a pipe or channel for conveying exhaust gases from a fireplace, oven, furnace, boiler or steam generator. Quite often, the flue gas refers to the combustion exhaust gas produced at power plants. Its composition depends on what is being burned, but it will usually consist of
When fuel is burned in a boiler, it produces flue gas, similar to the exhaust from your car. This gas leaves the combustion chamber and enters the flue passages. The combustion chamber and flue passages (called the heat exchanger) are surrounded by water the same water that is circulated throughout your home to deliver heat. By design, these
2008-7-10 · FLUE GAS RECIRCULATION SYSTEMS FOR STOKER BOILERS Flue Gas Recirculation (FGR) is a patented combustion modification process for stoker-fired boilers that will increase boiler efficiency and steaming capacity, while at the same time reduce particulates, stack opacity and NOx emissions. Emissions of sulfur oxides (SOx) can also be
2012-1-2 · December 2006 Combustion & Flue Gas Analysis 21 Excellence in measurements Boilers Wall-hang type : The body of the boiler is fitted on the wall 20-30 KW Floor-installation type : The boiler is fitted on the support or on the floor. 30-100 KW Heating + Hot Water or Hot Water only •
2019-5-12 · A flue-gas stack, also known as a smoke stack, chimney stack or simply as a stack, is a type of chimney, a vertical pipe, channel or similar structure through which combustion product gases called flue gases are exhausted to the outside air. Flue gases are produced when coal, oil, natural gas, wood or any other fuel is combusted in an industrial furnace, a power plant's steam-generating boiler
The flue gas analyser testo 330i is the further development of the proven exhaust gas measuring instrument testo 330-2 LL, and has the same precision and reliability as this Testo evergreen. The most important difference: The testo 330i is operated entirely via the testo 330i App and a
: 2 West Market Street, Suite 500, West Chester, PA 19382, United States2013-8-13 · 5 1. Foreword This handbook is a valuable reference work for the application of portable flue gas analyzer in industry. Frequent questions arising from practical use are answered
Flue Gas boilers are the significant energy saving equipment, utilize the heat in flue gas from combustion processes or hot extract air from industrial processes to generate hot water or saturated steam Otherwise, the flue gas boiler could be used in oil gas fired combined cycle units, and take advantage of the high temperature flue gas heat discharged by gas turbine