Product thermal capacity : 1-20 t/h Working pressure : 0.7-2 Mpa Available fuel : Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc. Available industries : Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc. Introduction:
lpg boiler will not fire is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
Technical advantages Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
1.5 Liquefied Petroleum Gas Combustion 1.5.1 General1 Liquefied petroleum gas (LPG or LP-gas) consists of propane, propylene, butane, and butylenes; the product used for domestic heating is composed primarily of propane. This gas, obtained mostly from gas wells (but also, to a lesser extent, as a refinery by-product) is stored as a liquid under
My gas boiler is not igniting – help! A gas boiler that is not igniting is as good as useless until it is repaired. Boilers need to ignite if your central heating and hot water taps are to work. However, finding out why a boiler is not working can be a challenge, and you will likely need the help of a Gas Safe engineer if you are to get the ...
Common Boiler Problems: Causes and Quick Fixes . While we always recommend calling a trained engineer to help with boiler problems, many technicians charge by the hour. Considering this, if you are able to diagnose the issue and take a few preliminary steps before you book a repair, you could save the engineers time and cut the cost of your ...
I have a CG-4-SPDL Propane Boiler that will not fire. The pilot is lit, and I have replaced the thermocouple. How do a I problem solve the most likely cause. It is New Year's Eve and very cold at -10 F. I have a wood boiler as heat back-up, but is does not have enough Btu available for the current temp conditions.
If your boiler was installed over 10 years ago then its about time to consider a replacement boiler. Older boilers are more susceptible to faults and don’t run as efficiently as they once might have done. Not taking action will lead to more and more faults and eventually a broken boiler.
Check your boiler’s pressure gauge. If it’s showing a reading of one bar or less, low pressure could be the reason why your boiler’s not working. Topping up the pressure yourself is usually straightforward - follow the steps in your boiler’s manual or watch our how-to video.
Help! My Boilers Not Working - 5 Things To Check Before Calling Your Gas Safe Engineer . Before you call your gas engineer to repair your broken boiler - check these 5 common boiler faults first! Let's face it, it's a whole load of hassle when your central heating boiler stops working.