Product thermal capacity : 1-20 t/h Working pressure : 0.7-2 Mpa Available fuel : Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc. Available industries : Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc. Introduction:
hot water boiler not circulating is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
Technical advantages Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Hot Water Heater Circulator Pumps: Hot Water Heat System Circulator Troubleshooting & Repair Guide Circulator pump relay switches & controls on heating systems: Troubleshooting & Repair Guide How to tell if a heating circulator pump is working Why do some heating zones work and others not, why does heat come out of zones where thermostats are not calling for heat?
Hot Water Not Circulating; Author: mmsitarski (NJ) I have a Weil-McClain Gold forced hot water boiler (oil). I have it set up as one zone. The burner fires and heats the water to 220 degrees (what the aquastat is set to) then the burner kicks off and the circulating pump stays on but the water does not circulate to the baseboards.
Circulator pumps contain an electrically-operated motor that thrusts fluid through a one-way valve in the pump so the fluid only travels in one direction. Your home heating system is a typical example for the use of a circulator pump. Circulator pumps can stop working for several reasons: a blown fuse, bad wiring or a dead motor.
My father's boiler is working and making hot water. It turns on around 175 and off around 195 degrees. The boiler is about 4 years old, maybe 5. The water is not circulating throughout the house, though. The bulk of the piping is about 30 years old. It has three zones.
Boiler Circulation Problems | Troubleshooting Hydronic Water Loops – Richard, we have a hot water boiler and we are having problems with the circulation of the water. . The radiators are cool and we don’t seem to have good he
This is Grundfos’ flagship hot water recirculation system. This timer unit is a bit above average in price but has a very high satisfaction rate. Installed at water heater. This is our #3 pick only because the price point is a bit higher than the Watts 500800.
In a traditional hot water recirculating system, there is a dedicated return line for the hot water pipes that goes from the furthest bathroom or fixture back to the water heater. Near the water heater area, a recirculating pump pulls the water from the furthest fixture back into the water heater, creating a loop.
In these hot water systems, once the radiator or baseboard convector is heated with the hot water, the cooled water is returned back to the boiler to be reheated, and the water circulation loop continues. Understanding the components of a hot water boiler helps you with basic troubleshooting steps.