Product thermal capacity : 1-20 t/h Working pressure : 0.7-2 Mpa Available fuel : Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc. Available industries : Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc. Introduction:
steam boiler thermostat wiring is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
Technical advantages Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
A steam boiler (Figure 5) would have a pressure control as a high-limit control, a low-water cutoff as a safety device, and a thermostat setting the comfort level. There will also be a rollout switch, a flue spill switch, and a flue damper.
You will not be required to run a new wire from your thermostat to your furnace/boiler. Below is a diagram illustrating how the ecobee would be wired with the common maker in this scenario. Note: The R wire must go into RC instead of RH. A C (common) wire must be identified at the furnace/boiler system for the Fast-Stat to connect to.
Wire the "Normally Open" relay contacts to the boiler's thermostat leads. Use the following thermostat cable hookup to the thermostat: Red to R or RH (depending on which thermostat you will use), White to W, Green to C. If the thermostat also operates an A/C unit, it should have two "Red" terminals: R or RH is for heat, RC is for cooling.
A boiler thermostat helps in controlling the boiler operation, thus maintaining a proper set temperature inside the home. As I noted above, there are different types of boiler systems like gas-fired boiler, steam boiler, and fuel oil based boiler.
brand boilers can do more, with less field wiring, and fewer aftermarket controls and components – improving the operation of both new and replacement boiler installations. These application drawings include detailed wiring diagrams, and set-up details, allowing installers to fully utilize the capability and
The boiler thermostat is one of the most important devices in the home, yet it is often overlooked. This relatively small device is responsible for controlling the level of heat in your home during the cooler months. In the past, boiler-thermostat wiring used to be rated for 110 volts, but now ...
A to steam boiler water heater wiring Central warm air furnace heat pump boiler for steam or hot water heating system built in or plug in room heater are heating stove and fireplace are a few examples of heating equipment. Heating Water flows backwards from the radiators to the boiler.