Product thermal capacity : 1-20 t/h Working pressure : 0.7-2 Mpa Available fuel : Nature gas, coke oven gas, biogas, methanol, liquid propane gas, diesel, heavy oil, light oil, crude oil, etc. Available industries : Heat supplying, chemical, food, textile, printing and dyeing, cigarettes and tobacco, fodder, pharmacy, building materials, brewery, rubber, hospital etc. Introduction:
iit high pressure boiler is a boiler shell type 3 passes wetback oil/gas fired boiler. After fuel is being atomized by burner, flame is full of the wave furnace and transfer heat via furnace wall, this is 1st pass; the high temperature smoke is collected in reversal chamber and then enters 2nd pass which is grooved tubes bundle area; after heat convection, air temperature gradually falls and goes to front smoke box and turn to 3rd pass, which is smooth tubes bundle area, and then enters chimney passing back smoke box and exhausted to the atmosphere.
Technical advantages Digitized manufacture
The key part such as material cutting, rolling, drilling are proceeded by advanced CNC machining process to reduce the assemble stress and extend boiler working lifetime.
The front and back smoke chamber plates are cut by CNC plasma cutting machine and looks tidy and beautiful.
Easy operation and maintenance
Fully automatically operating, with automatically adjustment and protection of burning, water level, temperature and steam pressure.
Longer working life
Smoke tube and tube sheet connection is expanded first to eliminate the gap between them, then adopt automatic argon arc welding to relief the stress and expand boilers working life.
Longitudinal and girth joint adopt advanced automatic submerged-arc welding for good welding quality. All longitudinal and girth joint will have 100% radiographic inspection.
Fin tube us ND steel or stainless-steel material which avoid low temperature corrosion.
Inspection procedure point is set up to guarantee the sequence of expanding and welding, avoid cracking of the tube sheet holes.
Less fuel consumption
High quality aluminum silicate fiber is used with fire clay insulation, to control the boiler body temperature below 45℃ to control heat lost.
Sufficient steam storage room and heating area makes boiler to generate high quality steam and high thermal power.
Condenser is added to reuse the waste heat of the exhausted smoke to increase feeding water’s temperature and reduce emission temperature, which can increase the thermal efficiency above 98% and save operating cost.
Tube failure in high pressure boilers follow a normal bath tub curve, with higher rate during initial operation period, stabilizing to a lower rate during the normal operating period and again increasing as the boilers age and cross ten to fifteen years of operation.
if you're boiler manual says it's maximum pressure is at or below 3 bar then fair enough (virtually all boiler manuals are available online), but every boiler installation should have a pressure relief valve that's set to relieve pressure before it becomes dangerous anyway, so it's very unlikely to be at a dangerous level.
Black Seal High-Pressure Operator Overview: The Black Seal, High Pressure license is required for boilers over 100 hp and more than 15 pounds pressure steam. If it's a hot water heating system the boilers must be over 160 psi with a water temperature over 250° Fahrenheit. Experience:
High Pressure Boilers continues to be the leading resource for preparing for high pressure boiler operator and facility operating engineer licensing. This textbook provides a comprehensive overview of the safe and efficient operation of high pressure steam boilers and related equipment.
This session explains the concept of specific steam consumption, and methods to improve the performance of Rankine Cycle by higher boiler pressure and superheating. Sign up now to enroll in courses, follow best educators, interact with the community and track your progress.
Temperatures in high-pressure boilers will exceed 250 degrees F. Because of the elevated pressure at which these boilers operate, they need to be monitored to ensure safety at all times. High-pressure boiler operators must inspect switches, valves, safety devices and leaks on a regular basis.
A boiler is called a high-pressure boiler when it operates with a steam pressure above 80 bars. The high-pressure boilers are widely used for power generation in thermal power plants. In a high-pressure boiler, if the feed-water pressure increases, the saturation temperature of water rises and the latent heat of vaporization decreases.
My boiler pressure is too high! Is your boiler pressure too high? If your boiler is still working, you probably shouldn’t worry yourself too much – there likely isn’t anything wrong with the appliance at all, and you may be able to get the boiler water pressure down to recommended levels without breaking a sweat.